Here we go fellow woodworkers! I started up my Dovetail-a-day plan on 1/1/13…not so much as a New Year’s resolution, rather giving myself a clear run of non-travel days that should find me home and in the shop for the next few weeks.
This post is pretty picture-intensive to show the tact I’m starting with for cutting my dovetails. Future posts will just include updates of my progress, and any changes I make to my technique…maybe driven by suggestions from any of you dovetail gurus out there (hint hint!) J
The last time I attempted hand-cut dovetails was probably about seven or eight years ago when my Dad gave me a lesson during one of our trips back east. I think I cut about a dozen joints during that visit and actually got some pretty good results. I haven’t hand cut any since that trip, so this new venture is heavily laced with some very sweet memories of my Dad.
Earlier in December I picked up some 1X6 pine boards (3/4” X 5 1/2") from Home Depot to use as practice stock. Yesterday morning I broke the boards down to one foot lengths. Each pair of boards should allow me to make three or four practice joints each.
With my first pair of boards selected I laid out the tools I’ll need to get the action started. I’ve got my Veritas Dovetail Saw (14 tpi) and the Crosscut Saw ready to go. I’m using a round bladed marking gauge and my Dad’s old Lie-Nielsen dovetail marker for laying out the joints. I’ll also be using my Stanley Sweetheart (750) chisels…a gift from my parents from a couple Christmases back.
My first step is to lay out the tails. I know that this will cause some immediate controversy, but it’s what made sense to me. J I set the marking gauge to the thickness of my boards. Since both boards are the same thickness there will only be this one setting.
I decided to cut a three tailed joint. This gives me plenty of room to work around the tails while I’m rebuilding my “chops.” I set a tail an inch in from both sides and centered the third. Then I marked the waste to protect me from myself!
After the layout it was time to dig in and make some cuts. My first attempts with Dad were with a Japanese style pull-saw, so this is my first time using the western style dovetail saws. So far I like both methods. Perhaps I’ll experiment with the Dozuki again in the future.
With the sides of the tails cut, it was time to go after removing the waste. I know that quite a few folks will use a coping or fret saw here, but I’m going to chop out the waste with chisels. This is a handy trick that Dad showed me all those years ago. By using the chisel to pare out a small wedge, a little “wall” is created that gives the saw a guide to start making a straight cut. The scribed line from the marking gauge does double duty here by providing a resting place for the chisel’s edge to sit in before striking it with the mallet. The wedge is then removed with a light paring cut.
This technique worked really well for me. It’s amazing how just a tiny, little shoulder is enough to guide the saw true when starting the cut.
I didn’t catch a photo, but did use this same technique to create those little “walls” when I started chopping out the waste from between the tails.
I alternated paring cuts and chopping cuts until I was about halfway through the board. I then flipped the board over and worked from the other side. Once most of the material was removed from around the base of the tails, the rest of the waste popped right out.
After a little clean-up with the chisels I used the tail board to mark the location of the pins on the second work piece.
I then followed all of the same procedures to cut the other half of the joint in the pin board…and here it is, my Day One efforts at hand cutting dovetails.
There are some gaps, and I can see where my saw cuts were not a true as I would have liked. I was pleased with my layout though. I can actually flip the tail board over and tails will match up with the pins. It’s not a perfect fit because of the variations created by my sawing, but the joint will slide together about half way and the edges are still aligned. One thing I did forget to do was time myself. I'll have to put a clock on my efforts going forward to measure any increase in efficiency as well as precision.
This was a great experience and I’m looking forward to practicing a lot more. I thought about Dad and missed him a lot while working on these. All that I remembered made me feel better and prouder than even the most perfect dovetail joints could.I’d love to hear some feedback or input on my technique. I know that there are many methods out there and that folks use all kinds of variations to produce amazing results. Thanks for visiting, and come on back!